氣體吸附式空氣干燥機

◆產品設備顯著特點 Product features

※更具固定高度的吸氣負擔和露點

1.粘附塔之寬度與的直徑經實驗英文報告單緊密測算，塔床障礙小，有保障了進行壓縮實驗室氣體干躁劑5秒的接觸性日子，能夠滿足的成品氣的露點追求。

2.30％的干劑加工余量，于補償金干劑的天然損壞，保障干。

3.大一些的擴撒器，為了保證暖濕氣流一致完成干燥處理劑層，削除溝流毛細現象。

※機體再生氣量損耗率值為14％

1.優良的機筒設計制作，同步保存100％的吸糖份，儲藏的糖份適用于加大復蘇關鍵期的復蘇氣室溫，增加機械設備的解吸的能力，使復蘇更恢復原狀。

2.干躁和機體機體再生用方向過流策劃方案，濕大氣流下干的樹脂吸附劑期限果較好的。機體機體再生氣用于出口含濕量管控在亞趨于穩定階段，使消音器及排氣閥門安全通道無結霜之慮。

3.可表明干熱機的使用電動機扭矩需求量改善恢復氣的使用量，切實保障恢復氣體流動不間斷穩定性，恢復壓低至臨界狀態。

※干劑動用時間長

1.比較適合的機筒寬度，使氣體順利通過干澀劑層的水流量和的時間保護好的方式，徹底的充分運用干澀劑的性能方面。

2.合理可行的體系配制，在氣旋進機筒前，經除油治療馬(ma)上去除氣旋中內含油份物與重生態破壞問題物，以免常溫、干燥劑層受生態破壞問題。

※機器通過了新穎別致高品控智能及自動化閥和穩定的全電子設備可語言編程序操作器，組排頁面融洽，自動化累計界面顯示雙塔情況，反復的周期性現廠可編，出廠的選用10min。管道閥門使用期限將近50萬次行為。

※鍋筒罐壁作冷鍍鋅管防銹處里處里，10年不生繡。

※健身動作更準確、性能指標不穩定性、工作非常簡單，裝設必須的基礎。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆最主要的科技產品參數 Main technical parameters